Foundation Mold Format Langstroth 423 x 200 mm

846,00 incl. VAT

Includes 19% VAT
Delivery Time: approx. 1-2 month

The foundation mold consists of two silicon honeycomb molds, which are mounted on distortion-proof aluminum plates with strong 240 V fans for cooling. The silicone skirt is attached to the wax outlet.
The silicone skirt and the special compressed air gun are included in the price.

The cell measure amounts to normally 5,4 mm.

Extra charge for special sizes on request »

This field can't be Empty
SKU: 104 Category:

Description

Advantages of the air cooled foundation mold

The cell measure amounts to normally 5,4 mm.
The foundation mold consists of two silicone honeycomb forms, which are applied on warpage safe aluminum plates, at which strong 240 V-blower for cooling is appropriate. At the wax discharge the silicone apron is downward fastened.

  • short setting up times by air cooling
  • the mold can be opened problem-free by the special air pressure pistole and the wax plate can be extracted, thus you can receive a yield onto 100%.
  • surplus wax flows back directly over the silicone apron into the melting pot.
  • time saving
  • no rips or locations of fracture in the wax plates by soft cooling
  • easy removal of the wax of the silicone parts
  • no delay of the mold and thus the thickness of the wax plates is even.

—————————————————————–

Incidentally, water-cooled molds are no longer contemporary, cumbersome to handle, and expensive to purchase and repair.

Productvideo

YouTube

Mit dem Laden des Videos akzeptieren Sie die Datenschutzerklärung von YouTube.
Mehr erfahren

Video laden

Why we should mould foundations ourselves?

By the application of varroa pesticides in the beekeeping get to more and more poisonous active substances in our beeswax. So in almost all foundations available at the market the varroazide are provably and can get therefore in our honey.
To avoid these unwanted loads from the beginning, all beekeepers should mould their foundations from untreated bee wax themselves. Wax of drone honeycombs and young wax of the honeycombs which have appeared from new foundations should be applied preferred for own wax cycle.
Therfore I have developed the foundation mold with direct wax return flow, it is simple in the handling and by the mutual air cooling will cool short times be reached. The so moulded foundations are free of tears and exact by the careful cool process.
With the help of compressed air and a special compressed air pistol the foundations are taken practically without touch, the yield amounts to 100 %.

How to do it

Cell measures – 5,3 mm.

Put the wax melting pot under the silicon apron. Then switch on the electrical blower and open the plate above.

Move the filled scoop over the lower pressure plate and fill out the hot wax.

When closing the form surplus wax runs back directly over the silicone apron into the wax fusion pot.

With the help of a putty the wax at the withdrawal edge must be removed.

To open the mold you blow first compressed air (max. 4-6 bar) with the help of a special compressed air nozzle between upper pressure plate and foundation mold. Thus the form can be opened without effort.

Subsequently, you blow air under the foundation and now you could take out the wax plate without difficulty. At the same time the form is cooled by the air leaking out.

After several casting processes you take the layer of wax off (after reaching at least 5 mm of thickness) of the silicone apron and melt them again.

Hints

The wax:  it should not become too hot, so an electrically heatable preserving pot (15 litres) with thermostat (temperature approx. 75 – 80 °C) is best suitable

Another tip:  You can change the thickness of the wax plates by turning the adjusting screws at the hinges.

Reviews

There are no reviews yet.

Be the first to review “Foundation Mold Format Langstroth 423 x 200 mm”

Your email address will not be published. Required fields are marked *